Mini Mania
Est. 1974
Shop by Car
 Live Help
800-946-2642
Search
All
Your Price $33.95
Qty:
Buy Now
by Selecting a
Variations below:
Brake Wear Sensor Oem Front - R55/56/57 Cooper $ S 2007-08/2010
Rear up to 08/2010
G2NMB2020$33.95
Brake Wear Sensor Oem Front - R55/56/57 Cooper $ S 2007-08/2010
Front up to 08/2010
G2NMB2021$35.95
Brake Wear Sensor Oem Front - R55/56/57/58/59 Cooper $ S 08/2010+
Front from 08/2010
G2NMB2221$35.95
Brake Wear Sensor Oem Rear - R55/56/57/58/59 Cooper $ S 08/2010+
Rear from 08/2010
G2NMB2220$33.95
Brake Wear Sensor Oem Rear - R55/56/57/58/59 Cooper $ S 08/2010+

Brake Wear Sensor Oem Rear - R55/56/57/58/59 Cooper $ S 08/2010+

Brake Wear Sensor Oem Rear - R55/56/57/58/59 Cooper $ S 08/2010+

Brake Wear Sensor Oem Rear - R55/56/57/58/59 Cooper $ S 08/2010+

Brake Wear Sensor Oem Rear - R55/56/57/58/59 Cooper $ S 08/2010+
MINI factory replacement REAR Brake Wear Sensor. These are factory original replacements. (Right Rear sensor).

Fits:

2007-08/2010 R56 Cooper and Cooper S Hardtop
2008-08/2010 R55 Cooper and Cooper S CLUBMAN
2009-08/2010 R57 Cooper and Cooper S Convertibles

Brake wear sensors are Production Date dependent. Two versions available for models built before 08/2010 and those built on or after 08/2010. Select accordingly.

If your brake wear warning light is illumnicated on your dash, either the front left or rear right wear sensor is worn. These are the replacements.

Each car requires one front and one rear sensor.

Fits both standard and JCW Brakes.

For 2002-2006 R50/R53 Hatchbacks and 2005-2008 R52 Convertibles, see NMB1014-P.

Brake fluid should be replaced every 2 years. See ATE Performance Brake Fluid for replacement brake fluid. ATE® Type 200 Amber is a high quality performance fluid that will last much longer than the standard DOT4 fluid. This is an ABS friendly fluid.

ATE® Super Blue and ATE® TYP 200 Amber has a dry boiling point of 536F and a wet boiling point of 396F which far exceeds standard brake fluids meeting the DOT 4 requirements. This fluid is NOT SILICONE and is compatible with conventional brake fluid. 100% synthetic fluid is specifically designed to resist the high temperatures of racing brakes and yet very suitable for daily driving.

4 Other Variations Available:
Brake Wear Sensor Oem Front - R55/56/57 Cooper $ S 2007-08/2010
Rear up to 08/2010
Brake Wear Sensor Oem Front - R55/56/57 Cooper $ S 2007-08/2010
Front up to 08/2010
Brake Wear Sensor Oem Front - R55/56/57/58/59 Cooper $ S 08/2010+
Front from 08/2010
Brake Wear Sensor Oem Rear - R55/56/57/58/59 Cooper $ S 08/2010+
Rear from 08/2010
Technical Information:
Resetting the Brake Wear Service Light
Additional Related Articles:

When the Brake Wear Service indicator light illuminates, one of the two Brake Wear Sensors has been triggered.  The brake wear sensor is a wire loop that gets worn down against the rotor.  Once the wire is worn thru and the circuit is opened, the brake wear indicator light is illuminated.

The MINI has a brake wear sensor in the front left wheel, and the right rear wheel.

After replacing the worn sensor, reset the service light with the following procedure:

 

For "Generation 1" 2002-2006 R50 and R53 Hatchback and 2005-2008 R52 Convertibles

A.  Turn the ignition key to the #2 position for around 30 seconds without turning over the engine
B.  The light should go out! 

 

For "Generation 2" 2007+ R56 Hatchbacks, 2008+ R55 CLUBMAN, and 2009+ R57 Convertibles

To enter the service Menu:

A. Insert Key
B. Do not press clutch / brake
C. Press Start button
D. Wait until the Car / revelant Service symbol disappears on the Rev counter display
E. Immediately after the symbol goes out - Press and hold Both buttons on the Rev Counter
F. Continue to hold - the system Will run a dash light check
G. Continue to hold
H. Display will then show VIN / Menu, - continue to hold through this until the time Reappears on the display.
I. Now release Only the Right hand Button (trip reset) for about a second, and then press and hold again (whilst still holding the LH button)
J. After another second or 2 the display will show the Front Brake Symbol You Are Now in the Service Menu:D
K. Use the BC Button (on indicator stalk) to scroll through to the relevant symbol - eg Rear Brakes
L. To Reset the warning indicator light - Press & Hold the BC Button at the revelant symbol until RESET appears - then press and hold again until the process is complete.

Turn Off and On the Ignition again - Warning should now have gone!

 

And if that didn't work, try this:


A.  Sit in car, close door and turn ignition on.
B.  Press and hold trip reset button for 10 seconds.
C. The upper display in the tach will be illuminated with a service item. the lower display in the tach will indicate the remaining time or mileage left for that service item. Pressing the BC (board computer) button repeadtedly on the end of the turn signal stalk wil allow the display to scroll through all of the condition based service items.
D.  To reset, press and hold the bc button again and the lower screen will indicate reset.
E.  Pressing the bc button only resets the item displayed in the upper window only. Repeat the procedure for any additional service reset needs.

 

 

Share on Facebook

 

 

Read Full Article
Customer Reviews
Write a customer review
Review this item and receive a $5 coupon off you're next purchase!* Click Here For Details
Click Here For Details