Classic Mini Cooper
Records - of
# |
Part No |
Qty |
Description |
|---|---|---|---|
| 1 | 22G1837 | 1 | Flywheel housing NLA, use FAM6257/9 |
| 1 | DAM6074 | 1 | Flywheel housing Turbo only |
| 1 | DAM6259 | 1 | Flywheel housing - use with AHU1707 or DAM3745 998cc, |
| 1 | TRD10015 | 1 | Flywheel housing, was DAM6257, use with AHU1707 1300cc (Breather hole) |
| 2 | AHU1707 | 1 | Idler bearing 1.375" 34.92mm O/D .875" I/D |
| 2 | DAM3745 | 1 | Idler bearing 1.375" 34.92mm O/D .750" I/D |
| 2 | 13H7848 | 1 | Idler bearing 1.065" 27.05mm O/D 4 synchro early |
| 2 | 88G302 | 1 | Idler bearing 1.004" 25.5mm O/D 3 synchro |
| 3 | AAU8424 | 1 | 1st motion shaft nose bearing, was 13H6080 13H6080 not interchangable |
| 3 | ADU6033 | 1 | 1st motion shaft nose bearing 1.692" 42.98mm O/D Turbo only |
| 4 | 2A3643 | 1 | Circlip for AAU8424 in flywheel housing |
| 4 | ADU7194 | 1 | Circlip for ADU6033 in flywheel housing Turbo only |
| 5 | CCN110 | 1 | Circlip for holding 1st motion shaft bearing |
| 6 | 13H2934 | 1 | Clutch oil seal (DAM2821 seal protector available) |
| 6 | LVF10005 | 1 | Clutch oil seal (reluctor type flywheel) Injection only |
| 7 | 22A2237 | 1 | Flywheel casing gasket |
| 7 | GUG705563GM | 1 | OEM Flywheel Housing Gasket |
| 8 | BH605141 | 3 | Clutch case screw, long was BH605141 DAM7758 bolt, alternative |
| 9 | GHF332 | 3 | Clutch case washer was LWZ305 |
| 10 | GHF103 | 3 | Screw, short was SH605081 DAM7753 bolt, alternative |
| 11 | 22A1762 | 1 | Locktab Part of 18G8086 |
| 12 | 22A1761 | 1 | Locktab Part of 18G8086 |
| 13 | 2A3521 | 1 | Locktab Part of 18G8086 |
| 14 | FNZ505 | 9 | Nut |
| 15 | GHF332 | 4 | Washer was LWZ305 |
| 16 | 22A1241 | 1 | Locktab Part of 18G8086 |
| 17 | 88G300 | 1 | Cover, with timing hole |
| 17 | AHU1106 | 1 | Cover - Verto with no timing hole |
| 18 | DAM7755 | 8 | Bolt - clutch cover |
| 19 | 2A3635 | 1 | Cover for timing hole |
| 20 | SH604041 | 2 | Screw for timing hole cover |
| 21 | GHF331 | 2 | Washer |
| 22 | 22A180 | 1 | Plunger, press fit for release bearing GRB201 |
| 22 | DAM1955 | 1 | Plunger, which takes GRB238 and DAM2413 Release bearing fit loose on plunger |
| 23 | DAM2413 | 1 | Clip, to hold GRB238 to DAM1955 |
| 24 | DAM5353 | 1 | Plunger verto clutch 1982 on |
| 25 | 22A427 | 1 | Plunger stop |
| 26 | NT610041 | 1 | Nut, was FNZ210 |
| 27 | 22A2204 | 1 | Clutch arm, was 2A3518, pre Verto |
| 28 | DAM5355 | 1 | Clutch arm short verto only 1982 on |
| 29 | CLZ628 | 1 | Clevis pin, lever to case |
| 30 | GHF302 | 1 | Washer, was PWZ106 |
| 31 | GHF101 | 1 | Adjusting screw was HZS409 |
| 32 | FNZ604 | 1 | Locking nut |
| 33 | CLZ518 | 1 | Clevis pin, lever to push rod |
| 34 | 2A3601 | 1 | Spring anchor |
| 35 | GHF301 | 1 | Washer was FWZ105 |
| 36 | 1G5999 | 1 | Clutch spring |
| 37 | 2A3600 | 1 | Anchor spring end Pre Verto |
| 38 | 13H396 | 1 | Slave cylinder push rod All Minis |
