× 1-800-946-2642 Home My Account Social / Forum Articles Contact My Cart
Shop Now
Select Your Car Type Sale Items Clearance Items New Items
   Forum Width:     Forum Type: 

 Posted: Sep 26, 2022 06:41AM
Total posts: 13954
Last post: Sep 26, 2022
Member since:Jan 22, 2003
Cars in Garage: 4
Photos: 381
WorkBench Posts: 1
CA

Installed just fine.

Didn't have a helper, so used a bar clamp against the pedal and square floor channel......worked well

 

"Everybody should own a MINI at some point, or you are incomplete as a human being" - James May

"WET COOPER", Partsguy1 (Terry Snell of Penticton BC ) - Could you send the money for the unpaid parts and court fees.
Ordered so by a Judge

 

 

 

 Posted: Sep 20, 2022 12:28PM
Total posts: 151
Last post: Sep 21, 2022
Member since:Feb 27, 2007
Cars in Garage: 6
Photos: 20
WorkBench Posts: 0
Quote:
Originally Posted by Alex
I've never bothered !
Bolt it on, couple the lines up, and pumpity-pump.
Same here, never bothered to bench prime a clutch or brake master cylinder (didn't know you could!)

"Nature Bats Last"
 Posted: Sep 20, 2022 01:38AM
Total posts: 10150
Last post: Sep 30, 2022
Member since:Mar 24, 1999
Cars in Garage: 0
Photos: 0
WorkBench Posts: 0
GB
I've never bothered !
Bolt it on, couple the lines up, and pumpity-pump.

 Posted: Sep 17, 2022 05:58PM
Total posts: 13954
Last post: Sep 26, 2022
Member since:Jan 22, 2003
Cars in Garage: 4
Photos: 381
WorkBench Posts: 1
CA
Thanks.....just thought I'd check before it arrives...hopefully Monday.
Yes...going in a RH steer car

 

"Everybody should own a MINI at some point, or you are incomplete as a human being" - James May

"WET COOPER", Partsguy1 (Terry Snell of Penticton BC ) - Could you send the money for the unpaid parts and court fees.
Ordered so by a Judge

 

 

 

 Posted: Sep 17, 2022 05:51PM
Total posts: 293
Last post: Sep 30, 2022
Member since:Jan 25, 2017
Cars in Garage: 0
Photos: 0
WorkBench Posts: 0
There is nothing hard about priming the master . Fill the container, hold your finger over the hole. push the  plunger into the cylinder and let the fluid out with finger. Hold the finger in place not allowing air to get suck back in as you pull the plunger bace out. do it a couple of times. You will still need to bleed when you install. If it is a RHD mini , I remember doing it when installed.

 Posted: Sep 17, 2022 05:09PM
Total posts: 13954
Last post: Sep 26, 2022
Member since:Jan 22, 2003
Cars in Garage: 4
Photos: 381
WorkBench Posts: 1
CA
come on boys.......is there a bench blead process?

 

"Everybody should own a MINI at some point, or you are incomplete as a human being" - James May

"WET COOPER", Partsguy1 (Terry Snell of Penticton BC ) - Could you send the money for the unpaid parts and court fees.
Ordered so by a Judge

 

 

 

 Posted: Sep 13, 2022 01:22PM
Total posts: 13954
Last post: Sep 26, 2022
Member since:Jan 22, 2003
Cars in Garage: 4
Photos: 381
WorkBench Posts: 1
CA
When installing one of the plastic reservoir masters.....is there a bench bleed process?  I can't remember.

 

"Everybody should own a MINI at some point, or you are incomplete as a human being" - James May

"WET COOPER", Partsguy1 (Terry Snell of Penticton BC ) - Could you send the money for the unpaid parts and court fees.
Ordered so by a Judge