Classic Mini Cooper 998cc, 1100cc & 998cc Cooper - To 1980
Records - of
# |
Part No |
Qty |
Description |
|---|---|---|---|
| BEB-08 | 1 | High-grade bolt kit |
|
| 1 | 12G123 | 2 | Connecting rod number 2 and 4 |
| 1 | 12G126 | 2 | Connecting rod number 1 and 3 |
| 2 | 2A660 | 4 | Locktab |
| 3 | 12G2217 | 8 | Big end bolt |
| 4 | 8G2733 | 1 | Crankshaft (casting number 12A595) (12A1451) 998cc and Cooper 998cc |
| 4 | 8G2732 | 1 | Crankshaft (casting number 12G82) 1100cc |
| 5 | 6K836 | 1 | Crankshaft key |
| 6 | VP572 | 1 | Con rod bearings, 1.625 Also in 10/20/40 oversize |
| 7 | VP733 | 1 | Mains bearings Also in 10/20/30/40 oversize |
| 8 | VPW81 | 1 set | Thrust washer set Also in 03/30 thou oversize |
| 9 | 22A1493 | 1 | Primary gear (24 teeth) |
| 10 | 22G401 | 1 | Bush front was 22G401 |
| 11 | 22G109 | 1 | Bush rear |
| 12 | 22A321 | 1 | Thrust washers 2.79-2.84mm (.110-112") These shims are used to give the correct end float of 3-6 thou on the primary gear check 22A319 and 88G459 for wear. |
| 12 | 22A322 | 1 | Thrust washers 2.84-2.89mm (.112-114") |
| 12 | 22A323 | 1 | Thrust washers 2.89-2.94mm (.114-116") |
| 12 | 22A324 | 1 | Thrust washers 2.94-2.99mm (.116-118") |
| 12 | 22A450 | 1 | Thrust washers 2.99-3.04mm (.118-120") |
| 13 | 22A319 | 1 | U Clip thrust |
| 14 | 88G549 | 1 | Backing ring |
| 15 | AEA630 | 1 | Camshaft 1100cc and 998cc Cooper |
| 15 | 8G712 | 1 | Camshaft 998cc |
| 16 | 2A299 | 1 | Camshaft oil pump drive NLA (Fitted in camshaft new) |
| 17 | WKN505 | 1 | Camshaft key pin |
| 18 | AHU2379 | 1 | Camshaft plate |
| 19 | GHF117 | 3 | Locating plate bolt |
| 20 | GHF321 | 3 | Locating bolt shakeproof washer |
| 21 | 2A85 | 1 | Camshaft gear with tensioners |
| 22 | 8G549 | 2 | Tensioner rubber rings |
| 23 | 12G4337 | 1 | Camshaft gear, used originally without tensioner |
| 24 | 12G2621 | 1 | Tensioner, fits 12G2626 front plate only From engine number 99H791, 10H791 Not 998 Cooper |
| 25 | 12G2628 | 1 | Tensioner mounting plate |
| 26 | 12G2629 | 1 | Pivot pin |
| 27 | 6K629 | 1 | Camshaft nut |
| 28 | 2A759 | 1 | Camshaft locktab |
| 29 | 8G725 | 1 | Crankshaft gear |
| 30 | 6K628 | 1 | Washer to shim crank gear |
| 31 | 3H2127 | 1 | Timing chain (Simplex) |
| 32 | 2A970 | 1 | Front plate - pre tensioner type NLA |
| 32 | 12G2626 | 1 | Front plate - used with tensioner pads |
| 33 | 12G619 | 1 | Gasket for 2A970 front plate |
| 33 | 12G2981 | 1 | Gasket for 12G2626 front plate |
| 34 | 12G4499 | 1 | Distributor drive spindle |
| 35 | 13H2792 | 1 | ‘O’ ring distributor housing |
| 36 | 12A1136 | 1 | Housing, Pre-A+ Distributor |
| 37 | 2A14 | 8 | Push rod |
| 38 | 2A13 | 8 | Cam follower |
| 38 | AEG584 | 8 | Cam follower with oil hole High-grade |
