The Ignitor has been proven for over fifteen years in race cars, off-road vehicles, national rental fleets, parcel delivery services and by backyard mechanics. The Ignitor is the ideal choice for collector car restoration because it fits entirely under the distributor cap for a neat, clean look. The Ignitor is made in the U.S.A.
Selected: 23D4 Distributor No Vacuum Advance
Select variations below for more info:
The Ignitor has been proven for over fifteen years in race cars, off-road vehicles, national rental fleets, parcel delivery services and by backyard mechanics. The Ignitor is the ideal choice for collector car restoration because it fits entirely under the distributor cap for a neat, clean look. The Ignitor is made in the U.S.A.
Question:
Looking for a positive ground 23d4 kit.
Answer:
That's likely this one: https://www.minimania.com/part/LU142-POS/Pertronix-Ignitor-Lucas-23d---25d-Positive-Ground-Only
Mini Mania Tech Team
The Classic Mini Parts and Accessories Experts
The Ignitor II uses a powerful micro controller with adaptive dwell algorithms resulting in the following features and benefits for your MINI:
· The Ignitor II senses current levels in the coil and adjusts the dwell to maintain peak energy throughout the entire RPM range. Dwell time is increased or decreased with changing engine RPM and operating conditions. This provides more energy at high RPM reducing misfires while improving engine performance.
· Compared to point type systems, develops on average 4 times more available energy between 3000 and 5000 RPM and 2 times more available plug voltage.
· Compared to the original Ignitor develops an average 3 times more available energy between 3000 and 5000 RPM and nearly doubles available plug voltage.
· Higher RPM performance is improved when used with new Flame-Thrower II super low resistance (0.6 ohms) 45,000 volt coil, however, is compatible with any induction coil.
· Because peak current level is reached just prior to spark, ignition energy is sustained with less heat build-up increasing coil and module life.
· Adjusts spark timing over the entire RPM range to compensate for the inherent electronic delay resulting in more stable timing.
· Senses engine startup and increases dwell time providing more energy for starting sparks.
· Senses incorrectly wired Ignitor II or a “key left on” condition and shuts down the system protecting the coil and other components from damage.
· Shares all the same form features as the Ignitor i.e. electronics molded in epoxy for better foul weather performance, no moving or rubbing parts to wear out, fits entirely inside the distributor, no “black box” to clutter your engine compartment, no complicated wiring makes installation easy, compatible with 12-volt negative ground systems and comes with a 30 month warranty.
· California Air Resources Board E.O. #D-57-8, legal in all 50 states and Canada Not to be used with solid core spark plug wires.
· The Ignitor II senses current levels in the coil and adjusts the dwell to maintain peak energy throughout the entire RPM range. Dwell time is increased or decreased with changing engine RPM and operating conditions. This provides more energy at high RPM reducing misfires while improving engine performance.
· Compared to point type systems, develops on average 4 times more available energy between 3000 and 5000 RPM and 2 times more available plug voltage.
· Compared to the original Ignitor develops an average 3 times more available energy between 3000 and 5000 RPM and nearly doubles available plug voltage.
· Higher RPM performance is improved when used with new Flame-Thrower II super low resistance (0.6 ohms) 45,000 volt coil, however, is compatible with any induction coil.
· Because peak current level is reached just prior to spark, ignition energy is sustained with less heat build-up increasing coil and module life.
· Adjusts spark timing over the entire RPM range to compensate for the inherent electronic delay resulting in more stable timing.
· Senses engine startup and increases dwell time providing more energy for starting sparks.
· Senses incorrectly wired Ignitor II or a “key left on” condition and shuts down the system protecting the coil and other components from damage.
· Shares all the same form features as the Ignitor i.e. electronics molded in epoxy for better foul weather performance, no moving or rubbing parts to wear out, fits entirely inside the distributor, no “black box” to clutter your engine compartment, no complicated wiring makes installation easy, compatible with 12-volt negative ground systems and comes with a 30 month warranty.
· California Air Resources Board E.O. #D-57-8, legal in all 50 states and Canada Not to be used with solid core spark plug wires.
Pertronix Ignitor Ii For 43/45d Red Fixed/blue SlidingPertronix Ignitor Ii For 43/45d Red Fixed/blue SlidingPertronix Ignitor Ii For 43/45d Red Fixed/blue SlidingPertronix Ignitor Ii For 43/45d Red Fixed/blue SlidingPertronix Ignitor Ii For 43/45d Red Fixed/blue SlidingPertronix Ignitor Ii For 43/45d Red Fixed/blue SlidingPertronix Ignitor Ii For 43/45d Red Fixed/blue SlidingPertronix Ignitor Ii For 43/45d Red Fixed/blue SlidingPertronix Ignitor Ii For 43/45d Red Fixed/blue Sliding
Selected: Ignitor II
Alternate Products
$153.98
Pertronix Ignitor Conversion Kit For Lucas 43 45 & 59D Distributors
The Ignitor II uses a powerful micro controller with adaptive dwell algorithms resulting in the following features and benefits for your MINI:
· The Ignitor II senses current levels in the coil and adjusts the dwell to maintain peak energy throughout the entire RPM range. Dwell time is increased or decreased with changing engine RPM and operating conditions. This provides more energy at high RPM reducing misfires while improving engine performance.
· Compared to point type systems, develops on average 4 times more available energy between 3000 and 5000 RPM and 2 times more available plug voltage.
· Compared to the original Ignitor develops an average 3 times more available energy between 3000 and 5000 RPM and nearly doubles available plug voltage.
· Higher RPM performance is improved when used with new Flame-Thrower II super low resistance (0.6 ohms) 45,000 volt coil, however, is compatible with any induction coil.
· Because peak current level is reached just prior to spark, ignition energy is sustained with less heat build-up increasing coil and module life.
· Adjusts spark timing over the entire RPM range to compensate for the inherent electronic delay resulting in more stable timing.
· Senses engine startup and increases dwell time providing more energy for starting sparks.
· Senses incorrectly wired Ignitor II or a “key left on” condition and shuts down the system protecting the coil and other components from damage.
· Shares all the same form features as the Ignitor i.e. electronics molded in epoxy for better foul weather performance, no moving or rubbing parts to wear out, fits entirely inside the distributor, no “black box” to clutter your engine compartment, no complicated wiring makes installation easy, compatible with 12-volt negative ground systems and comes with a 30 month warranty.
· California Air Resources Board E.O. #D-57-8, legal in all 50 states and Canada Not to be used with solid core spark plug wires.
· The Ignitor II senses current levels in the coil and adjusts the dwell to maintain peak energy throughout the entire RPM range. Dwell time is increased or decreased with changing engine RPM and operating conditions. This provides more energy at high RPM reducing misfires while improving engine performance.
· Compared to point type systems, develops on average 4 times more available energy between 3000 and 5000 RPM and 2 times more available plug voltage.
· Compared to the original Ignitor develops an average 3 times more available energy between 3000 and 5000 RPM and nearly doubles available plug voltage.
· Higher RPM performance is improved when used with new Flame-Thrower II super low resistance (0.6 ohms) 45,000 volt coil, however, is compatible with any induction coil.
· Because peak current level is reached just prior to spark, ignition energy is sustained with less heat build-up increasing coil and module life.
· Adjusts spark timing over the entire RPM range to compensate for the inherent electronic delay resulting in more stable timing.
· Senses engine startup and increases dwell time providing more energy for starting sparks.
· Senses incorrectly wired Ignitor II or a “key left on” condition and shuts down the system protecting the coil and other components from damage.
· Shares all the same form features as the Ignitor i.e. electronics molded in epoxy for better foul weather performance, no moving or rubbing parts to wear out, fits entirely inside the distributor, no “black box” to clutter your engine compartment, no complicated wiring makes installation easy, compatible with 12-volt negative ground systems and comes with a 30 month warranty.
· California Air Resources Board E.O. #D-57-8, legal in all 50 states and Canada Not to be used with solid core spark plug wires.
The two best features of the new Pertronix Ignitor electronic ignition conversion kit for your MINI are the low price and the fact that it fits entirely inside your stock distributor cap! All previous ignition kits utilized an external black box, not the sort of thing you want under the hood of your stock-looking engine compartment! And, like the more expensive electronic ignition kits, once you install the magnetic trigger and sensor, you will never have to change points again! Available for early, 23/25D(low tension lead clips onto the distributor body) early side and top entry caps(LU142) or late, 45D (LU143) distributors. Now available in POSITIVE ground, part number LU142-POS! Use "Pull down menu" on right side of this screen to dtermine various applications.
For "flamethrower" coil by Pertronix, for use with LU142, see part #40001.
For "flamethrower" coil by Pertronix, for use with LU142, see part #40001.
Pertronix Ignitor 23/25d Negative GroundPertronix Ignitor 23/25d Negative GroundPertronix Ignitor 23/25d Negative GroundPertronix Ignitor 23/25d Negative GroundPertronix Ignitor 23/25d Negative GroundPertronix Ignitor 23/25d Negative GroundPertronix Ignitor 23/25d Negative GroundPertronix Ignitor 23/25d Negative Ground
Selected: Ignitor 23/25d negative ground
Alternate Products
$177.98
Pertronics Ignitor Lucas 23d / 25d Coil- Positive Ground Only
The two best features of the new Pertronix Ignitor electronic ignition conversion kit for your MINI are the low price and the fact that it fits entirely inside your stock distributor cap! All previous ignition kits utilized an external black box, not the sort of thing you want under the hood of your stock-looking engine compartment! And, like the more expensive electronic ignition kits, once you install the magnetic trigger and sensor, you will never have to change points again! Available for early, 23/25D(low tension lead clips onto the distributor body) early side and top entry caps(LU142) or late, 45D (LU143) distributors. Now available in POSITIVE ground, part number LU142-POS! Use "Pull down menu" on right side of this screen to dtermine various applications.
For "flamethrower" coil by Pertronix, for use with LU142, see part #40001.
For "flamethrower" coil by Pertronix, for use with LU142, see part #40001.
The two best features of the new Pertronix Ignitor electronic ignition conversion kit are the low price and the fact that it fits entirely inside your stock distributor cap in your MINI! (POSITIVE ground only!) All previous ignition kits utilized an external black box, not the sort of thing you want under the hood of yoir stock-looking engine compartment! And, like the more expensive electronic ignition kits, once you install the magnetic trigger and sensor, you will never have to change points again! Also, available for early, 23/25D Negative Ground (LU142) or late, 45D (LU143) distributors. For "flamethrower" coil by Pertronix, for use with LU142, see part #40001.
Pertronics Ignitor Lucas 23d / 25d Coil- Positive Ground OnlyPertronics Ignitor Lucas 23d / 25d Coil- Positive Ground OnlyPertronics Ignitor Lucas 23d / 25d Coil- Positive Ground OnlyPertronics Ignitor Lucas 23d / 25d Coil- Positive Ground OnlyPertronics Ignitor Lucas 23d / 25d Coil- Positive Ground OnlyPertronics Ignitor Lucas 23d / 25d Coil- Positive Ground OnlyPertronics Ignitor Lucas 23d / 25d Coil- Positive Ground Only
Selected: 23D/25D Positive ground only
Alternate Products
$177.98
Pertronics Ignitor Lucas 23d / 25d Coil- Positive Ground Only
The two best features of the new Pertronix Ignitor electronic ignition conversion kit are the low price and the fact that it fits entirely inside your stock distributor cap in your MINI! (POSITIVE ground only!) All previous ignition kits utilized an external black box, not the sort of thing you want under the hood of yoir stock-looking engine compartment! And, like the more expensive electronic ignition kits, once you install the magnetic trigger and sensor, you will never have to change points again! Also, available for early, 23/25D Negative Ground (LU142) or late, 45D (LU143) distributors. For "flamethrower" coil by Pertronix, for use with LU142, see part #40001.
The two best features of the new Pertronix Ignitor electronic ignition conversion kit are the low price and the fact that it fits entirely inside your stock distributor cap! (POSITIVE ground only!) All previous ignition kits utilized an external black box, not the sort of thing you want under the hood of yoir stock-looking engine compartment! And, like the more expensive electronic ignition kits, once you install the magnetic trigger and sensor, you will never have to change points again! Also, available for early, 23/25D Negative Ground (LU142) or late, 45D (LU143) distributors.
Pertronix Ignitor: Lucas 43d - 45d / Red Fixed Points - PPertronix Ignitor: Lucas 43d - 45d / Red Fixed Points - PPertronix Ignitor: Lucas 43d - 45d / Red Fixed Points - PPertronix Ignitor: Lucas 43d - 45d / Red Fixed Points - PPertronix Ignitor: Lucas 43d - 45d / Red Fixed Points - PPertronix Ignitor: Lucas 43d - 45d / Red Fixed Points - P
Selected: 43D/45D Red fixed positive ground
Alternate Products
$177.98
Pertronics Ignitor Lucas 23d / 25d Coil- Positive Ground Only
The two best features of the new Pertronix Ignitor electronic ignition conversion kit are the low price and the fact that it fits entirely inside your stock distributor cap! (POSITIVE ground only!) All previous ignition kits utilized an external black box, not the sort of thing you want under the hood of yoir stock-looking engine compartment! And, like the more expensive electronic ignition kits, once you install the magnetic trigger and sensor, you will never have to change points again! Also, available for early, 23/25D Negative Ground (LU142) or late, 45D (LU143) distributors.
Many of the later model Mini has the Ducellier distributors installed in them from the factory. If you have one of these distributors and are tired of having to constantly replace the points, etc. and then having a hard time finding them, perhaps it is time for an upgrade to electronic ignition. This kit from Pertronix is very easy to install and can be done with a few hand tools. Never Change points again!
Austin Mini Pertronox Ignitor - Ducelier Ccw (52594a)Austin Mini Pertronox Ignitor - Ducelier Ccw (52594a)Austin Mini Pertronox Ignitor - Ducelier Ccw (52594a)Austin Mini Pertronox Ignitor - Ducelier Ccw (52594a)Austin Mini Pertronox Ignitor - Ducelier Ccw (52594a)
Selected: Duceller ccw (525294A)
Alternate Products
$177.98
Pertronics Ignitor Lucas 23d / 25d Coil- Positive Ground Only
Many of the later model Mini has the Ducellier distributors installed in them from the factory. If you have one of these distributors and are tired of having to constantly replace the points, etc. and then having a hard time finding them, perhaps it is time for an upgrade to electronic ignition. This kit from Pertronix is very easy to install and can be done with a few hand tools. Never Change points again!
Pertronix Ignitor conversion kits transform your old points distributor to a new, super reliable and consistently accurate electric distributor. This kit is for the Lucas 25D4 distributors. Negative ground cars only.
- 12-Volt Negative Ground
- Adaptive dwell maintains peak energy throughout the entire RPM range, reducing misfires while improving engine performance.
- Develops on average 4 times more available energy between 3000 and 5000 RPM, and 2 times more available plug voltage.
- Compensates for inherent electronic delay by adjusting the spark timing throughout the entire RPM range.
- Synchronized peak current and spark timing reduces heat build-up.
- Senses startup and develops more energy for quicker, easier starting.
- Pair with a Flame Thrower Canister Coil for optimal performance
- Legal in all 50 states and Canada (C.A.R.B. E.O. #D-57-22)
Pertronix Ignitor II Lucas 25D4 Electronic Conversion KitPertronix Ignitor II Lucas 25D4 Electronic Conversion KitPertronix Ignitor II Lucas 25D4 Electronic Conversion KitPertronix Ignitor II Lucas 25D4 Electronic Conversion Kit
Selected: Pertronix Ignitor II Lucas 25D4 Conversion
Alternate Products
$177.98
Pertronics Ignitor Lucas 23d / 25d Coil- Positive Ground Only
Pertronix Ignitor conversion kits transform your old points distributor to a new, super reliable and consistently accurate electric distributor. This kit is for the Lucas 25D4 distributors. Negative ground cars only.
- 12-Volt Negative Ground
- Adaptive dwell maintains peak energy throughout the entire RPM range, reducing misfires while improving engine performance.
- Develops on average 4 times more available energy between 3000 and 5000 RPM, and 2 times more available plug voltage.
- Compensates for inherent electronic delay by adjusting the spark timing throughout the entire RPM range.
- Synchronized peak current and spark timing reduces heat build-up.
- Senses startup and develops more energy for quicker, easier starting.
- Pair with a Flame Thrower Canister Coil for optimal performance
- Legal in all 50 states and Canada (C.A.R.B. E.O. #D-57-22)
Use this Pertronix kit to convert Lucas type 43,45, and 59D contact points distributors to fully electronic units. The two best features of the new Pertronix Ignitor electronic ignition conversion kit are the low price and the fact that it fits entirely inside your stock distributor cap! (Negative ground only!) All previous ignition kits utilized an external black box, not the sort of thing you want under the hood of your stock-looking engine compartment! And, like the more expensive electronic ignition kits, once you install the magnetic trigger and sensor, you will never have to change points again!
Pertronix Ignitor Conversion Kit For Lucas 43 45 & 59D DistributorsPertronix Ignitor Conversion Kit For Lucas 43 45 & 59D DistributorsPertronix Ignitor Conversion Kit For Lucas 43 45 & 59D Distributors
Pertronix Ignitor Conversion Kit For Lucas 43 45 & 59D DistributorsPertronix Ignitor Conversion Kit For Lucas 43 45 & 59D DistributorsPertronix Ignitor Conversion Kit For Lucas 43 45 & 59D Distributors
Selected: 43D/45D/59D, Negative Ground
Alternate Products
$139.95
Classic Mini Electronic Ignition Kit For The 43, 45, & 59d Distributors
Use this Pertronix kit to convert Lucas type 43,45, and 59D contact points distributors to fully electronic units. The two best features of the new Pertronix Ignitor electronic ignition conversion kit are the low price and the fact that it fits entirely inside your stock distributor cap! (Negative ground only!) All previous ignition kits utilized an external black box, not the sort of thing you want under the hood of your stock-looking engine compartment! And, like the more expensive electronic ignition kits, once you install the magnetic trigger and sensor, you will never have to change points again!
This is the Pertronix kit for Mallory distributor models 23,24,and YL dual point non vacuum. Get rid of the points and install electronic ingition in your Mallory distributor get best of both worlds.
Pertronix Ignitor System For Mallory DistributorsPertronix Ignitor System For Mallory Distributors
Selected: Mallory distributors
Alternate Products
$139.95
Classic Mini Electronic Ignition Kit For The 43, 45, & 59d Distributors
This is the Pertronix kit for Mallory distributor models 23,24,and YL dual point non vacuum. Get rid of the points and install electronic ingition in your Mallory distributor get best of both worlds.
The Ignitor II uses a powerful micro controller with adaptive dwell algorithms resulting in the following features and benefits:
· The Ignitor II senses current levels in the coil and adjusts the dwell to maintain peak energy throughout the entire RPM range. Dwell time is increased or decreased with changing engine RPM and operating conditions. This provides more energy at high RPM reducing misfires while improving engine performance.
· Compared to point type systems, develops on average 4 times more available energy between 3000 and 5000 RPM and 2 times more available plug voltage.
· Compared to the original Ignitor develops an average 3 times more available energy between 3000 and 5000 RPM and nearly doubles available plug voltage.
· Higher RPM performance is improved when used with new Flame-Thrower II super low resistance (0.6 ohms) 45,000 volt coil, however, is compatible with any induction coil.
· Because peak current level is reached just prior to spark, ignition energy is sustained with less heat build-up increasing coil and module life.
· Adjusts spark timing over the entire RPM range to compensate for the inherent electronic delay resulting in more stable timing.
· Senses engine startup and increases dwell time providing more energy for starting sparks.
· Senses incorrectly wired Ignitor II or a “key left on” condition and shuts down the system protecting the coil and other components from damage.
· Shares all the same form features as the Ignitor i.e. electronics molded in epoxy for better foul weather performance, no moving or rubbing parts to wear out, fits entirely inside the distributor, no “black box” to clutter your engine compartment, no complicated wiring makes installation easy, compatible with 12-volt negative ground systems and comes with a 30 month warranty.
· California Air Resources Board E.O. #D-57-8, legal in all 50 states and Canada Not to be used with solid core spark plug wires.
· The Ignitor II senses current levels in the coil and adjusts the dwell to maintain peak energy throughout the entire RPM range. Dwell time is increased or decreased with changing engine RPM and operating conditions. This provides more energy at high RPM reducing misfires while improving engine performance.
· Compared to point type systems, develops on average 4 times more available energy between 3000 and 5000 RPM and 2 times more available plug voltage.
· Compared to the original Ignitor develops an average 3 times more available energy between 3000 and 5000 RPM and nearly doubles available plug voltage.
· Higher RPM performance is improved when used with new Flame-Thrower II super low resistance (0.6 ohms) 45,000 volt coil, however, is compatible with any induction coil.
· Because peak current level is reached just prior to spark, ignition energy is sustained with less heat build-up increasing coil and module life.
· Adjusts spark timing over the entire RPM range to compensate for the inherent electronic delay resulting in more stable timing.
· Senses engine startup and increases dwell time providing more energy for starting sparks.
· Senses incorrectly wired Ignitor II or a “key left on” condition and shuts down the system protecting the coil and other components from damage.
· Shares all the same form features as the Ignitor i.e. electronics molded in epoxy for better foul weather performance, no moving or rubbing parts to wear out, fits entirely inside the distributor, no “black box” to clutter your engine compartment, no complicated wiring makes installation easy, compatible with 12-volt negative ground systems and comes with a 30 month warranty.
· California Air Resources Board E.O. #D-57-8, legal in all 50 states and Canada Not to be used with solid core spark plug wires.
Pertronix Ignitor Ii: Lucas 43d - 45d / Blue Sliding Points
Selected: Ignitor II - 43/45D type w/blue sliding points
Alternate Products
$139.95
Classic Mini Electronic Ignition Kit For The 43, 45, & 59d Distributors
The Ignitor II uses a powerful micro controller with adaptive dwell algorithms resulting in the following features and benefits:
· The Ignitor II senses current levels in the coil and adjusts the dwell to maintain peak energy throughout the entire RPM range. Dwell time is increased or decreased with changing engine RPM and operating conditions. This provides more energy at high RPM reducing misfires while improving engine performance.
· Compared to point type systems, develops on average 4 times more available energy between 3000 and 5000 RPM and 2 times more available plug voltage.
· Compared to the original Ignitor develops an average 3 times more available energy between 3000 and 5000 RPM and nearly doubles available plug voltage.
· Higher RPM performance is improved when used with new Flame-Thrower II super low resistance (0.6 ohms) 45,000 volt coil, however, is compatible with any induction coil.
· Because peak current level is reached just prior to spark, ignition energy is sustained with less heat build-up increasing coil and module life.
· Adjusts spark timing over the entire RPM range to compensate for the inherent electronic delay resulting in more stable timing.
· Senses engine startup and increases dwell time providing more energy for starting sparks.
· Senses incorrectly wired Ignitor II or a “key left on” condition and shuts down the system protecting the coil and other components from damage.
· Shares all the same form features as the Ignitor i.e. electronics molded in epoxy for better foul weather performance, no moving or rubbing parts to wear out, fits entirely inside the distributor, no “black box” to clutter your engine compartment, no complicated wiring makes installation easy, compatible with 12-volt negative ground systems and comes with a 30 month warranty.
· California Air Resources Board E.O. #D-57-8, legal in all 50 states and Canada Not to be used with solid core spark plug wires.
· The Ignitor II senses current levels in the coil and adjusts the dwell to maintain peak energy throughout the entire RPM range. Dwell time is increased or decreased with changing engine RPM and operating conditions. This provides more energy at high RPM reducing misfires while improving engine performance.
· Compared to point type systems, develops on average 4 times more available energy between 3000 and 5000 RPM and 2 times more available plug voltage.
· Compared to the original Ignitor develops an average 3 times more available energy between 3000 and 5000 RPM and nearly doubles available plug voltage.
· Higher RPM performance is improved when used with new Flame-Thrower II super low resistance (0.6 ohms) 45,000 volt coil, however, is compatible with any induction coil.
· Because peak current level is reached just prior to spark, ignition energy is sustained with less heat build-up increasing coil and module life.
· Adjusts spark timing over the entire RPM range to compensate for the inherent electronic delay resulting in more stable timing.
· Senses engine startup and increases dwell time providing more energy for starting sparks.
· Senses incorrectly wired Ignitor II or a “key left on” condition and shuts down the system protecting the coil and other components from damage.
· Shares all the same form features as the Ignitor i.e. electronics molded in epoxy for better foul weather performance, no moving or rubbing parts to wear out, fits entirely inside the distributor, no “black box” to clutter your engine compartment, no complicated wiring makes installation easy, compatible with 12-volt negative ground systems and comes with a 30 month warranty.
· California Air Resources Board E.O. #D-57-8, legal in all 50 states and Canada Not to be used with solid core spark plug wires.
The Ignitor has been proven for over fifteen years in race cars, off-road vehicles, national rental fleets, parcel delivery services and by backyard mechanics. The Ignitor is the ideal choice for collector car restoration because it fits entirely under the distributor cap for a neat, clean look. The Ignitor is made in the U.S.A.
Loading...
Loading...
Loading...
Loading...
Loading...
Loading...
Loading...
Related Technical Articles:
Created: December 28, 2018
/Mini%20Mania%20Catalog.Distributors.46.pdf
Created: December 12, 2013
In the early 70’s, an engineer came up with the idea of an electronic ignition system that would replace the points and condenser in distributors. The Ignitor® was born and after patenting the product, Per-Lux started manufacturing systems.
Created: February 01, 2006
Frequently Asked Questions about the use of the Pertronix Ignitor systems. The best information available from the experts at Minimania.com
- Home
- Related Websites
- Products
- Articles & Help
- Social
- Visit us on:
-
Mini Mania
870 Gold Flat Rd.
Nevada City, CA 95959 USAPhone: 530.470.8300
Fax: 530.470.8388
Your Login Failed.
Your E-Mail and/or password are incorrect. Please try again.
Passwords are case-sentive.
If you continue to have problems click on the Help Icon for additional options.
Login with your E-Mail Address. If you would like your login information reset, click on the button below to request your login information to be resent.