× 1-800-946-2642 Home My Account Social / Forum Articles Contact My Cart
Shop Now
Select Your Car Type Sale Items Clearance Items New Items
Modern high lift, short duration camshafts have posed quite a few problems for the general public in recent years. Widely available performance valve springs were outdated overnight, as it became necessary to reduce spring crush. This, in turn, caused low valve seat pressures creating valve float at high rpm. Mini Spares has massively simplified these problems by introducing a small range of springs that covers all eventualities. Manufactured from superquality silicone wire imported from Switzerland, their resistance against fading and breaking is extremely high. They are also designed to take standard type top caps. They can be fitted directly to the head with no fear of spring crush.
240lb Dual springs for race use up to 8000 rpm and .570 lift.
The standard fitted length of springs is 1.4" - 1.42". Spacer shims are available to increase valve seat poundage and overall spring rate. If the spring or valve seats in the head have already been machined, it will be necessary to re-shim to the correct fitted length. Also fits a Sprite , and MG Midget .

This valve spring set has been developed to fit standard sized top caps, and cope with racing rpm and high valve lifts without crushing of up to 0.570” without modifications, when fitted to a cylinder head that has standard or near standard valve spring heights. However, where possible, it is always advantageous to correct and match the valve spring heights (measured from the spring seat in the head to the underside of the spring retainer cap), as these will vary particularly where new valve seats are cut. The standard heights for pre-A+ heads are approximately 1.375” to 1.38” for small-bore types, 1.40” to 1.42” for large-bore types, and A+ heads 1.42” to 1.44” for small-bore types and 1.35”-1.37” for large-bore types. However, it must be stressed that these values are entirely dependant on the components used and machined condition of the head. Adjustments can be made by machining the spring seats, using shims of varying thickness or a mixture of both to achieve equalisation.

At 1.40” fitted height, these springs will give a seat load of approximately 82.08-psi (80-90-psi being preferred for race use). To calculate different loads for different height add/subtract 3.23-psi per 0.010” difference – for either seat or valve lift at the tip values.

To calculate approximate seat load at 1.35” fitted length –
1.40”-1.35” = 0.050”.
0.050” divided by 0.010” = 5
5 x 3.23-psi = 16.15-psi
Therefore new seat load at 1.35” will be -
82.08-psi + 16.15-psi = 98.23-psi

To calculate approximate load at the valve tip at any given valve lift – for example 0.500” –
0.500” divided by 0.010” = 50
50 x 3.23-psi = 161.5-psi
Therefore load at 0.500” valve lift, where fitted height is 1.40”, will be -
161.5-psi + 82.08-psi = 243.58-psi

Note: Valve lift value will obviously change with change in fitted height load, so make this calculation first. Rocker gear ratio will also alter over-all rate/load as seen by the cam/follower. To assess this, multiply valve tip load by actual rocker ratio – i.e. for 1.5 actual ratio with above 0.500” value – 1.5 x 243.58-psi = 365.37-psi.

It is ABSOLUTELY ESSENTIAL that the fitted height is NOT LESS than 1.42”. This will give a seat pressure of approximately 75-psi – the absolute minimum advised for race use, and where spring shuffle is to be avoided.

Useful part numbers:

C-AEA526 Nominal 180 psi dual valve springs, road/rally use up to 0.495" lift/7,500 rpm continual use.
C-AEA527 Nominal 240 psi dual valve springs, rally/race use up to 0.570" lift.
C-AEA528 Alloy top cap set, hard anodised, very light, single groove collet only.
AEA653 Steel 'W' type top caps, single groove collet only, need 8.
C-AEA654 Competition inner spring locator (no step).
AEA403 Standard lower inner spring locator, need 8.
SS4 Set of 4 spring spacer-shims, 0.080" thick.
88G459 Single groove collet, need 8 (come in pairs).
ADU4905 Valve stem seal, late 'sprung' type.
AEG327 Valve stem seal 'S' type without spring.
Classic Austin Mini-Cylinder head valve springs 240lbs anti bind 570 lift

Classic Austin Mini-Cylinder head valve springs 240lbs anti bind 570 lift

Classic Austin Mini-Cylinder head valve springs 240lbs anti bind 570 lift
Part No: C-AEA527
$72.95
Qty:
Fits the following:
Classic Mini
Sprite & MG Midget
Morris Minor
PayPal Pay Later
Alternate Products
Classic Austin Mini valve spring set 200lbs at 515 thou lift at 8000 rpm
$69.95 Classic Austin Mini valve spring set 200lbs at 515 thou lift at 8000 rpm
Classic Austin Mini Valve Spring Dual Isky 260lbs
$182.98 Classic Austin Mini Valve Spring Dual Isky 260lbs
Modern high lift, short duration camshafts have posed quite a few problems for the general public in recent years. Widely available performance valve springs were outdated overnight, as it became necessary to reduce spring crush. This, in turn, caused low valve seat pressures creating valve float at high rpm. Mini Spares has massively simplified these problems by introducing a small range of springs that covers all eventualities. Manufactured from superquality silicone wire imported from Switzerland, their resistance against fading and breaking is extremely high. They are also designed to take standard type top caps. They can be fitted directly to the head with no fear of spring crush.
240lb Dual springs for race use up to 8000 rpm and .570 lift.
The standard fitted length of springs is 1.4" - 1.42". Spacer shims are available to increase valve seat poundage and overall spring rate. If the spring or valve seats in the head have already been machined, it will be necessary to re-shim to the correct fitted length. Also fits a Sprite , and MG Midget .

This valve spring set has been developed to fit standard sized top caps, and cope with racing rpm and high valve lifts without crushing of up to 0.570” without modifications, when fitted to a cylinder head that has standard or near standard valve spring heights. However, where possible, it is always advantageous to correct and match the valve spring heights (measured from the spring seat in the head to the underside of the spring retainer cap), as these will vary particularly where new valve seats are cut. The standard heights for pre-A+ heads are approximately 1.375” to 1.38” for small-bore types, 1.40” to 1.42” for large-bore types, and A+ heads 1.42” to 1.44” for small-bore types and 1.35”-1.37” for large-bore types. However, it must be stressed that these values are entirely dependant on the components used and machined condition of the head. Adjustments can be made by machining the spring seats, using shims of varying thickness or a mixture of both to achieve equalisation.

At 1.40” fitted height, these springs will give a seat load of approximately 82.08-psi (80-90-psi being preferred for race use). To calculate different loads for different height add/subtract 3.23-psi per 0.010” difference – for either seat or valve lift at the tip values.

To calculate approximate seat load at 1.35” fitted length –
1.40”-1.35” = 0.050”.
0.050” divided by 0.010” = 5
5 x 3.23-psi = 16.15-psi
Therefore new seat load at 1.35” will be -
82.08-psi + 16.15-psi = 98.23-psi

To calculate approximate load at the valve tip at any given valve lift – for example 0.500” –
0.500” divided by 0.010” = 50
50 x 3.23-psi = 161.5-psi
Therefore load at 0.500” valve lift, where fitted height is 1.40”, will be -
161.5-psi + 82.08-psi = 243.58-psi

Note: Valve lift value will obviously change with change in fitted height load, so make this calculation first. Rocker gear ratio will also alter over-all rate/load as seen by the cam/follower. To assess this, multiply valve tip load by actual rocker ratio – i.e. for 1.5 actual ratio with above 0.500” value – 1.5 x 243.58-psi = 365.37-psi.

It is ABSOLUTELY ESSENTIAL that the fitted height is NOT LESS than 1.42”. This will give a seat pressure of approximately 75-psi – the absolute minimum advised for race use, and where spring shuffle is to be avoided.

Useful part numbers:

C-AEA526 Nominal 180 psi dual valve springs, road/rally use up to 0.495" lift/7,500 rpm continual use.
C-AEA527 Nominal 240 psi dual valve springs, rally/race use up to 0.570" lift.
C-AEA528 Alloy top cap set, hard anodised, very light, single groove collet only.
AEA653 Steel 'W' type top caps, single groove collet only, need 8.
C-AEA654 Competition inner spring locator (no step).
AEA403 Standard lower inner spring locator, need 8.
SS4 Set of 4 spring spacer-shims, 0.080" thick.
88G459 Single groove collet, need 8 (come in pairs).
ADU4905 Valve stem seal, late 'sprung' type.
AEG327 Valve stem seal 'S' type without spring.
Loading...
Loading...
Loading...
Loading...
Loading...
Loading...
Loading...
Loading...
Loading...
Loading...
Loading...
Loading...
Related Technical Articles:
Classic Mini Cooper Head Gaskets & Valve Springs page 29
Created: January 03, 2019
Complete head gasket selection for your 1959 thru 2000 Classic Mini Cooper. Performance and stock head gaskets for all size engines. Complete head gasket sets also available. Cylinder head valve springs for all models from 850 thru 1275cc engines both performance and stock are also available.
Classic Mini Cylinder head - What can easily be achieved
Created: February 03, 2011
The engine build I recently covered in previous Mini Magazine issues developed into a bit of an ongoing 'project'. During a discourse with the editorial staff at Mini Mag, it was decided the build feature presented an ideal opportunity to demonstrate just exactly what such an engine build is capable of in days where it's generally believed you have to have an all-singing, all-dancing 1380cc engine to have an enjoyable road burner - leaving those with very limited budgets a little depressed.