Fits the following models:

2007-2013 R56 MINI Cooper and MINI Cooper S Hardtops
2008-2014 R55 MINI Cooper and MINI Cooper S Clubman
2009-2015 R57 MINI Cooper and MINI Cooper S Convertible
2012-2015 R58 MINI Cooper and MINI Cooper S Coupe
2012-2015 R59 MINI Cooper and MINI Cooper S Roadster

These are performance street pads that produce less brake dust (medium dust rating) than the factory pads while offering improved braking performance. These pads use Aramid fibers. Compatible with MINI brake wear sensors.

Premium street sport pad for cars up to 200bhp.
General spirited street driving.

Designed for premium street driving offering better brake effect up to 600°C (1100°F). EBC Greenstuff has a high initial brake effect and gives drivers confidence from first application of the brake pedal. There is no such thing as a NO DUST pad. The very nature of how a brake works requires that some dust be generated to avoid rotor vibration (shimmying). The EBC pad creates less dust and dust is more easily washed off than most. All pads create more dust as they are bedding in especially if rotors are worn. Nominal friction coefficient 0.55. For faster cars and vehicles above 200bhp we strongly recommend Redstuff which DOES offer much less dust.

These pads are coated with 'BRAKE-IN SURFACE COATING'.
[ ] Effective immediately after installation.
[ ] Conditions rotor surface.
[ ] Prevents early life noise.
[ ] Helps pads bed-in fast.

NOTE:
Brakes are a safety critical part of your vehicle and should be installed by a competent mechanic following vehicle manufacturers installation procedure. The surface of these brake pads is coated with a red coating known as BRAKE-IN. This coating helps your newly installed brake pads to 'seat' or bed-in quickly. However, pads should be used gently for the first 100 miles until optimum braking is observed. Being a hard wearing pad, bed-in times can be as long as 1000 miles and drivers must be patient until the pad takes up the shape of their disc (brake rotor).

Rotors should be replaced with new when installing new brake pads. Failure to do so can result in brake noise as well as reduced braking efficiency. Avoid contamination of pad surface with any forms of grease that you may use to lubricate caliper sliders.

Manufacturers Warranty applies.

The entire green range is approved to ECE R90 for highway use.

For High Performance Brake Fluids, see the following:

• Ate Performance Brake Fluid - Very Good
• Motul Racing Brake Fluid - Better
• Torque Racing Brake Fluid - Best

For 'standard' replacement Brake Fluid, see Mini Cooper Brake Fluid Pentosin DOT4.

See G2NMB2022 for a listing of all options.

Fits the following Cooper S models:

2007-2013 R56 MINI Cooper S Hardtops
2008-2014 R55 MINI Cooper S Clubman
2009-2015 R57 MINI Cooper S Convertible
2012-2015 R58 MINI Cooper S Coupe
2012-2015 R59 MINI Cooper S Roadster
2011-2016 R60 MINI Cooper S Countryman including JCW models
2013-2016 R61 MINI Cooper S Paceman including JCW models

For other options, see G2NMB2022-P.

These are performance street pads that produce less brake dust (medium dust rating) than the factory pads while offering improved braking performance. These pads use Aramid fibers. Compatible with MINI brake wear sensors.

Premium street sport pad for cars up to 200bhp.
General spirited street driving.

Designed for premium street driving offering better brake effect up to 600°C (1100°F). EBC Greenstuff has a high initial brake effect and gives drivers confidence from first application of the brake pedal. There is no such thing as a NO DUST pad. The very nature of how a brake works requires that some dust be generated to avoid rotor vibration (shimmying). The EBC pad creates less dust and dust is more easily washed off than most. All pads create more dust as they are bedding in especially if rotors are worn. Nominal friction coefficient 0.55. For faster cars and vehicles above 200bhp we strongly recommend Redstuff which DOES offer much less dust.

These pads are coated with 'BRAKE-IN SURFACE COATING'.
[ ] Effective immediately after installation.
[ ] Conditions rotor surface.
[ ] Prevents early life noise.
[ ] Helps pads bed-in fast.

NOTE:
Brakes are a safety critical part of your vehicle and should be installed by a competent mechanic following vehicle manufacturers installation procedure. The surface of these brake pads is coated with a red coating known as BRAKE-IN. This coating helps your newly installed brake pads to 'seat' or bed-in quickly. However, pads should be used gently for the first 100 miles until optimum braking is observed. Being a hard wearing pad, bed-in times can be as long as 1000 miles and drivers must be patient until the pad takes up the shape of their disc (brake rotor).

Rotors should be replaced with new when installing new brake pads. Failure to do so can result in brake noise as well as reduced braking efficiency. Avoid contamination of pad surface with any forms of grease that you may use to lubricate caliper sliders.

Manufacturers Warranty applies.

The entire green range is approved to ECE R90 for highway use.

For High Performance Brake Fluids, see the following:

• Ate Performance Brake Fluid - Very Good
• Motul Racing Brake Fluid - Better
• Torque Racing Brake Fluid - Best

For 'standard' replacement Brake Fluid, see Mini Cooper Brake Fluid Pentosin DOT4.

Fits the following Cooper (non-S) models:

2007-2013 R56 MINI Cooper Hardtops
2008-2014 R55 MINI Cooper Clubman
2009-2015 R57 MINI Cooper Convertible
2012-2015 R58 MINI Cooper Coupe
2012-2015 R59 MINI Cooper Roadster
2011-2016 R60 MINI Cooper Countryman
2013-2016 R61 MINI Cooper Paceman

These are performance street pads that produce less brake dust (medium dust rating) than the factory pads while offering improved braking performance. These pads use Aramid fibers. Compatible with MINI brake wear sensors.

See G2NMB2022 for rear pads or Cooper S fronts.

Premium street sport pad for cars up to 200bhp.
General spirited street driving.

Designed for premium street driving offering better brake effect up to 600°C (1100°F). EBC Greenstuff has a high initial brake effect and gives drivers confidence from first application of the brake pedal. There is no such thing as a NO DUST pad. The very nature of how a brake works requires that some dust be generated to avoid rotor vibration (shimmying). The EBC pad creates less dust and dust is more easily washed off than most. All pads create more dust as they are bedding in especially if rotors are worn. Nominal friction coefficient 0.55. For faster cars and vehicles above 200bhp we strongly recommend Redstuff which DOES offer much less dust.

These pads are coated with 'BRAKE-IN SURFACE COATING'.
[ ] Effective immediately after installation.
[ ] Conditions rotor surface.
[ ] Prevents early life noise.
[ ] Helps pads bed-in fast.

NOTE:
Brakes are a safety critical part of your vehicle and should be installed by a competent mechanic following vehicle manufacturers installation procedure. The surface of these brake pads is coated with a red coating known as BRAKE-IN. This coating helps your newly installed brake pads to 'seat' or bed-in quickly. However, pads should be used gently for the first 100 miles until optimum braking is observed. Being a hard wearing pad, bed-in times can be as long as 1000 miles and drivers must be patient until the pad takes up the shape of their disc (brake rotor).

Rotors should be replaced with new when installing new brake pads. Failure to do so can result in brake noise as well as reduced braking efficiency. Avoid contamination of pad surface with any forms of grease that you may use to lubricate caliper sliders.

Manufacturers Warranty applies.

The entire green range is approved to ECE R90 for highway use.

For High Performance Brake Fluids, see the following:

• Ate Performance Brake Fluid - Very Good
• Motul Racing Brake Fluid - Better
• Torque Racing Brake Fluid - Best

For 'standard' replacement Brake Fluid, see Mini Cooper Brake Fluid Pentosin DOT4.

Fits the REAR brakes on the following model:

2011+ R60 Mini Cooper and Cooper S Countryman
2013+ R61 Mini Cooper and Cooper S Paceman

For other position or for Cooper S, see G2NMB2022-P.

These are performance street pads that produce less brake dust (medium dust rating) than the factory pads while offering improved braking performance. These pads use Aramid fibers. Compatible with MINI brake wear sensors.

Premium street sport pad for cars up to 200bhp.
General spirited street driving.

Designed for premium street driving offering better brake effect up to 600°C (1100°F). EBC Greenstuff has a high initial brake effect and gives drivers confidence from first application of the brake pedal. There is no such thing as a NO DUST pad. The very nature of how a brake works requires that some dust be generated to avoid rotor vibration (shimmying). The EBC pad creates less dust and dust is more easily washed off than most. All pads create more dust as they are bedding in especially if rotors are worn. Nominal friction coefficient 0.55. For faster cars and vehicles above 200bhp we strongly recommend Redstuff which DOES offer much less dust.

These pads are coated with 'BRAKE-IN SURFACE COATING'.
[ ] Effective immediately after installation.
[ ] Conditions rotor surface.
[ ] Prevents early life noise.
[ ] Helps pads bed-in fast.

For stock MINI factory replacement pads, see G2NMB2150.

NOTE:
Brakes are a safety critical part of your vehicle and should be installed by a competent mechanic following vehicle manufacturers installation procedure. The surface of these brake pads is coated with a red coating known as BRAKE-IN. This coating helps your newly installed brake pads to 'seat' or bed-in quickly. However, pads should be used gently for the first 100 miles until optimum braking is observed. Being a hard wearing pad, bed-in times can be as long as 1000 miles and drivers must be patient until the pad takes up the shape of their disc (brake rotor).

Rotors should be replaced with new when installing new brake pads. Failure to do so can result in brake noise as well as reduced braking efficiency. Avoid contamination of pad surface with any forms of grease that you may use to lubricate caliper sliders.

Manufacturers Warranty applies.

The entire green range is approved to ECE R90 for highway use.

See ATE Super Blue for replacement brake fluid. ATE Super Blue is a high quality performance fluid that will last much longer than the standard DOT4 fluid. This is an ABS friendly fluid.

ATE® Super Blue has a dry boiling point of 536F and a wet boiling point of 396F which far exceeds standard brake fluids meeting the DOT 4 requirements. This fluid is NOT SILICONE and is compatible with conventional brake fluid. 100% synthetic fluid is specifically designed to resist the high temperatures of racing brakes and yet very suitable for daily driving.