Fits the following Cooper S models:

2007-2013 R56 MINI Cooper S Hardtops
2008-2014 R55 MINI Cooper S Clubman
2009-2015 R57 MINI Cooper S Convertible
2012-2015 R58 MINI Cooper S Coupe
2012-2015 R59 MINI Cooper S Roadster
2011-2016 R60 Mini Cooper S Countryman including JCW models
2013-2016 R61 Mini Cooper S Paceman including JCW models

See G2NMB2025-P for rear pads or Cooper fronts.

Superstreet formula for Modified MINIs and fastest street driving.

This material is an Aramid fibre based brake compound enhanced with ceramic particles. Updated from the previous generation pre-ceramic compound, this material is light years ahead. It lasts longer, it brakes better and is quieter. Being a hard wearing pad, bed-in times can be as long as 1000 miles and drivers must be patient until the pad takes up the shape of their disc (brake rotor).

This is a truly impressive fast road pad for repeated heavy braking. It emits far less dust than semi-metallic pads and has been proven to stop a passenger car/sedan/sport compact/hot hatch 13 metres quicker than OEM pads from 100mph/160kph. Features EBC Brake-In surface coating which conditions rotor surface and accelerates pad bed-in. Nominal friction coefficient 0.5 with approx. 50% dust reduction compared to other pads.

Features:
* High Initial Brake Effect
* Strong Resistance To Fade Under Load
* Reduced Rotor Wear
* Low Dusting Of Wheels
* Shimmed; Chamfered; And Slotted
* Features EBC Brake-In Coating For Fast Break In
* Zero Noise And Extended Lifetime
* Accepts factory brake wear sensor

Manufacturers Warranty applies.

If your brake wear warning light is illumninated, see replacement sensors.

For High Performance Brake Fluids, see the following:

• Ate Performance Brake Fluid - Very Good
• Motul Racing Brake Fluid - Better
• Torque Racing Brake Fluid - Best

For 'standard' replacement Brake Fluid, see Mini Cooper Brake Fluid Pentosin DOT4.

NOTE:
Brakes are a safety critical part of your vehicle and should be installed by a competent mechanic following vehicle manufacturers installation procedure. The surface of these brake pads is coated with a red coating known as BRAKE-IN. This coating helps your newly installed brake pads to 'seat' or bed-in quickly. However, pads should be used gently for the first 100 miles until optimum braking is observed. Being a hard wearing pad, bed-in times can be as long as 1000 miles and drivers must be patient until the pad takes up the shape of their disc (brake rotor).

Rotors should be replaced with new when installing new brake pads. Failure to do so can result in brake noise as well as reduced braking efficiency. Avoid contamination of pad surface with any forms of grease that you may use to lubricate caliper sliders.

Fits the following models:

2007-2013 R56 MINI Cooper and MINI Cooper S Hardtops
2008-2014 R55 MINI Cooper and MINI Cooper S Clubman
2009-2015 R57 MINI Cooper and MINI Cooper S Convertible
2012-2015 R58 MINI Cooper and MINI Cooper S Coupe
2012-2015 R59 MINI Cooper and MINI Cooper S Roadster

See G2NMB2025-P front pads.

Superstreet formula for Modified MINIs and fastest street driving.

This material is an Aramid fibre based brake compound enhanced with ceramic particles. Updated from the previous generation pre-ceramic compound, this material is light years ahead. It lasts longer, it brakes better and is quieter. Being a hard wearing pad, bed-in times can be as long as 1000 miles and drivers must be patient until the pad takes up the shape of their disc (brake rotor).

This is a truly impressive fast road pad for repeated heavy braking. It emits far less dust than semi-metallic pads and has been proven to stop a passenger car/sedan/sport compact/hot hatch 13 metres quicker than OEM pads from 100mph/160kph. Features EBC Brake-In surface coating which conditions rotor surface and accelerates pad bed-in. Nominal friction coefficient 0.5 with approx. 50% dust reduction compared to other pads.

Features:
* High Initial Brake Effect
* Strong Resistance To Fade Under Load
* Reduced Rotor Wear
* Low Dusting Of Wheels
* Shimmed; Chamfered; And Slotted
* Features EBC Brake-In Coating For Fast Break In
* Zero Noise And Extended Lifetime
* Accepts factory brake wear sensor

Manufacturers Warranty applies.

If your brake wear warning light is illumninated, see replacement sensors.

For High Performance Brake Fluids, see the following:

• Ate Performance Brake Fluid - Very Good
• Motul Racing Brake Fluid - Better
• Torque Racing Brake Fluid - Best

For 'standard' replacement Brake Fluid, see Mini Cooper Brake Fluid Pentosin DOT4.

See G2NMB2025 for front pads.

NOTE:
Brakes are a safety critical part of your vehicle and should be installed by a competent mechanic following vehicle manufacturers installation procedure. The surface of these brake pads is coated with a red coating known as BRAKE-IN. This coating helps your newly installed brake pads to 'seat' or bed-in quickly. However, pads should be used gently for the first 100 miles until optimum braking is observed. Being a hard wearing pad, bed-in times can be as long as 1000 miles and drivers must be patient until the pad takes up the shape of their disc (brake rotor).

Rotors should be replaced with new when installing new brake pads. Failure to do so can result in brake noise as well as reduced braking efficiency. Avoid contamination of pad surface with any forms of grease that you may use to lubricate caliper sliders.

Fits the following Cooper (non-S) models:

2007-2013 R56 MINI Cooper Hardtop
2008-2014 R55 MINI Cooper Clubman
2009-2015 R57 MINI Cooper Convertible
2012-2015 R58 MINI Cooper Coupe
2012-2015 R59 MINI Cooper Roadster
2011-2016 R60 MINI Cooper Countryman
2013-2016 R61 MINI Cooper Paceman

Superstreet formula for Modified MINIs and fastest street driving.

See G2NMB2025-P for rear pads or Cooper S fronts.

This material is an Aramid fibre based brake compound enhanced with ceramic particles. Updated from the previous generation pre-ceramic compound, this material is light years ahead. It lasts longer, it brakes better and is quieter. Being a hard wearing pad, bed-in times can be as long as 1000 miles and drivers must be patient until the pad takes up the shape of their disc (brake rotor).

This is a truly impressive fast road pad for repeated heavy braking. It emits far less dust than semi-metallic pads and has been proven to stop a passenger car/sedan/sport compact/hot hatch 13 metres quicker than OEM pads from 100mph/160kph. Features EBC Brake-In surface coating which conditions rotor surface and accelerates pad bed-in. Nominal friction coefficient 0.5 with approx. 50% dust reduction compared to other pads.

Features:
* High Initial Brake Effect
* Strong Resistance To Fade Under Load
* Reduced Rotor Wear
* Low Dusting Of Wheels
* Shimmed; Chamfered; And Slotted
* Features EBC Brake-In Coating For Fast Break In
* Zero Noise And Extended Lifetime
* Accepts factory brake wear sensor

NOTE:
Brakes are a safety critical part of your vehicle and should be installed by a competent mechanic following vehicle manufacturers installation procedure. The surface of these brake pads is coated with a red coating known as BRAKE-IN. This coating helps your newly installed brake pads to 'seat' or bed-in quickly. However, pads should be used gently for the first 100 miles until optimum braking is observed. Being a hard wearing pad, bed-in times can be as long as 1000 miles and drivers must be patient until the pad takes up the shape of their disc (brake rotor).

Rotors should be replaced with new when installing new brake pads. Failure to do so can result in brake noise as well as reduced braking efficiency. Avoid contamination of pad surface with any forms of grease that you may use to lubricate caliper sliders.

Manufacturers Warranty applies.

For High Performance Brake Fluids, see the following:

• Ate Performance Brake Fluid - Very Good
• Motul Racing Brake Fluid - Better
• Torque Racing Brake Fluid - Best

For 'standard' replacement Brake Fluid, see Mini Cooper Brake Fluid Pentosin DOT4.

Fits the REAR brakes on the following model:

2011+ R60 Mini Cooper and Cooper S Countryman including JCW
2013+ R61 Mini Cooper and Cooper S Paceman including JCW

For other Redstuff Pads, see G2NMB2025-P.

Superstreet formula for Modified MINIs and fastest street driving.

This material is an Aramid fibre based brake compound enhanced with ceramic particles. Updated from the previous generation pre-ceramic compound, this material is light years ahead. It lasts longer, it brakes better and is quieter. Being a hard wearing pad, bed-in times can be as long as 1000 miles and drivers must be patient until the pad takes up the shape of their disc (brake rotor).

This is a truly impressive fast road pad for repeated heavy braking. It emits far less dust than semi-metallic pads and has been proven to stop a passenger car/sedan/sport compact/hot hatch 13 metres quicker than OEM pads from 100mph/160kph. Features EBC Brake-In surface coating which conditions rotor surface and accelerates pad bed-in. Nominal friction coefficient 0.5 with approx. 50% dust reduction compared to other pads.

Features:
* High Initial Brake Effect
* Strong Resistance To Fade Under Load
* Reduced Rotor Wear
* Low Dusting Of Wheels
* Shimmed; Chamfered; And Slotted
* Features EBC Brake-In Coating For Fast Break In
* Zero Noise And Extended Lifetime
* Accepts factory brake wear sensor

For stock MINI factory replacement pads, see G2NMB2150.

Manufacturers Warranty applies.

If your brake wear warning light is illumninated, see replacement sensors.

See ATE Super Blue to upgrade your MINI's brake fluid. ATE® Super Blue DOT 4 Racing Brake fluid is an ideal choice for handling the high demands placed on your MINI's brake system, regardless of whether you are involved in autocross, road racing or high performance street driving.

ATE® Super Blue has a dry boiling point of 536F and a wet boiling point of 396F which far exceeds standard brake fluids meeting the DOT 4 requirements. This fluid is NOT SILICONE and is compatible with conventional brake fluid. 100% synthetic fluid is specifically designed to resist the high temperatures of racing brakes and yet very suitable for daily driving.

NOTE:
Brakes are a safety critical part of your vehicle and should be installed by a competent mechanic following vehicle manufacturers installation procedure. The surface of these brake pads is coated with a red coating known as BRAKE-IN. This coating helps your newly installed brake pads to 'seat' or bed-in quickly. However, pads should be used gently for the first 100 miles until optimum braking is observed. Being a hard wearing pad, bed-in times can be as long as 1000 miles and drivers must be patient until the pad takes up the shape of their disc (brake rotor).

Rotors should be replaced with new when installing new brake pads. Failure to do so can result in brake noise as well as reduced braking efficiency. Avoid contamination of pad surface with any forms of grease that you may use to lubricate caliper sliders.