The Stage 1+ Suspention Upgrade Kit blends the racing performance experience of Mini Mania with the demands of the enthusiastic MINI street driver. Aggressive 'lowered' look with much improved handling!
Fits the following models:
2014-2023 F56 MINI Cooper and Cooper S Hardtop
2015-2023 F55 MINI Cooper and Cooper S Hardtop 4-Door
2016-2023 F57 MINI Cooper and Cooper S Convertible
Kit includes:
- Performance Lowering Springs
- 22mm Rear Anti-Sway Bar
- One pair Rear Adjustable Control Arms
MINI did a wonderful job with the handling on the new 3rd generation F-series MINI, but their design is on the conservative side to appeal to the widest segment of the market. This leaves room for improvement for the 'enthusiast' type driver.
When we talk about 'improving' the suspension, we always begin with a larger rear sway bar. This upgrade reduces the inherent 'understeer' built into the car for safety and provides a more 'balanced' car. This allows you to carry more speed into and out of the corner while keeping the car 'flatter' in the corners.
The Lowering Springs lowers the center of gravity allowing a quicker turn-in response and also helps to keep the car flatter in the corner.
Anytime the MINI is lowered, the rear negative camber is greatly increased and needs to be corrected. This is the reason for the Adjustable Rear Control Arms included in this kit. This kit inludes a pair of these adjustable arms which will allow you to correct the negative camber.
REAR ANTI-SWAY BAR
Front wheel drive cars naturally understeer from the factory, even the MINIs. The NM Engineering Solid 22mm Rear Anti Sway Bar improves your F-chassis MINI by enducing more oversteer and increasing the car handling predictability.
NM Eng Anti Sway Bar features:
- mandrel bent solid chromoly bar providing consistent diameter through out for precise torsioning motion
- forged ends (not cheaply welded plate) with two adjustment mounting holes
- graphite impregnated urethane bushing
- glossy blue powder coat finish
See NM Rear Sway Bar installation instructions here.
LOWERING SPRINGS
NM Engineering's RS Alpha progressive rate spring kits provide a responsive ride, sharper handling characteristics and lowered ride height. Using exacting spring rates and precision manufacturing techniques, RSa springs provide a more pleasurable motoring experience.
Lowering Rate:
B46/48 (2.0T)
Front: 33mm (1.30")
Rear: 31mm (1.22")
B38 (1.5T)
Front: 30mm (1.2")
Rear: 30mm (1.2")
Drop rates may slightly vary depending on transmission type and fuel level.
Notes: Finish : Powder Coated NM Blue
REAR ADJUSTABLE CONTROL ARMS
Introducing the newly redesigned NM Engineering Control Arm kit. While others use 1" diameter 6061 aluminum material, NM machines our control arms utilizing aerospace grade 7075-T6 1 1/4" hex aluminum bars, finished with titanium tint Type III / Mil-Spec Anodize. The use of larger material provides rigidity and strength of steel bar but without the weight.
NM Control Arm Kit also features precision heavy duty rod ends made from heat treated hardened steel with self lubricating nylon race. The threaded rod ends allow user to dial the suspension camber to desired specs, crucial for the weekend track enthusiasts and professional racers. T-303 stainless steel is used for the spacers to avoid any flexing and crushing caused by suspension load.
Optional Rubber Rod End Boot Kit protects the rod ends against dirt and grime that may cause performance noise. Available separately.
The Stage 1+ Suspention Upgrade Kit blends the racing performance experience of Mini Mania with the demands of the enthusiastic MINI street driver. Aggressive 'lowered' look with much improved handling!
Fits the following models:
2014-2023 F56 MINI Cooper and Cooper S Hardtop
2015-2023 F55 MINI Cooper and Cooper S Hardtop 4-Door
2016-2023 F57 MINI Cooper and Cooper S Convertible
Kit includes:
- Performance Lowering Springs
- 22mm Rear Anti-Sway Bar
- One pair Rear Adjustable Control Arms
MINI did a wonderful job with the handling on the new 3rd generation F-series MINI, but their design is on the conservative side to appeal to the widest segment of the market. This leaves room for improvement for the 'enthusiast' type driver.
When we talk about 'improving' the suspension, we always begin with a larger rear sway bar. This upgrade reduces the inherent 'understeer' built into the car for safety and provides a more 'balanced' car. This allows you to carry more speed into and out of the corner while keeping the car 'flatter' in the corners.
The Lowering Springs lowers the center of gravity allowing a quicker turn-in response and also helps to keep the car flatter in the corner.
Anytime the MINI is lowered, the rear negative camber is greatly increased and needs to be corrected. This is the reason for the Adjustable Rear Control Arms included in this kit. This kit inludes a pair of these adjustable arms which will allow you to correct the negative camber.
REAR ANTI-SWAY BAR
Front wheel drive cars naturally understeer from the factory, even the MINIs. The NM Engineering Solid 22mm Rear Anti Sway Bar improves your F-chassis MINI by enducing more oversteer and increasing the car handling predictability.
NM Eng Anti Sway Bar features:
- mandrel bent solid chromoly bar providing consistent diameter through out for precise torsioning motion
- forged ends (not cheaply welded plate) with two adjustment mounting holes
- graphite impregnated urethane bushing
- glossy blue powder coat finish
See NM Rear Sway Bar installation instructions here.
LOWERING SPRINGS
NM Engineering's RS Alpha progressive rate spring kits provide a responsive ride, sharper handling characteristics and lowered ride height. Using exacting spring rates and precision manufacturing techniques, RSa springs provide a more pleasurable motoring experience.
Lowering Rate:
B46/48 (2.0T)
Front: 33mm (1.30")
Rear: 31mm (1.22")
B38 (1.5T)
Front: 30mm (1.2")
Rear: 30mm (1.2")
Drop rates may slightly vary depending on transmission type and fuel level.
Notes: Finish : Powder Coated NM Blue
REAR ADJUSTABLE CONTROL ARMS
Introducing the newly redesigned NM Engineering Control Arm kit. While others use 1" diameter 6061 aluminum material, NM machines our control arms utilizing aerospace grade 7075-T6 1 1/4" hex aluminum bars, finished with titanium tint Type III / Mil-Spec Anodize. The use of larger material provides rigidity and strength of steel bar but without the weight.
NM Control Arm Kit also features precision heavy duty rod ends made from heat treated hardened steel with self lubricating nylon race. The threaded rod ends allow user to dial the suspension camber to desired specs, crucial for the weekend track enthusiasts and professional racers. T-303 stainless steel is used for the spacers to avoid any flexing and crushing caused by suspension load.
Optional Rubber Rod End Boot Kit protects the rod ends against dirt and grime that may cause performance noise. Available separately.
Loading...
Loading...
Loading...
Loading...
Loading...
-
Price : $355.13
-
Price : $362.22
-
Price : $461.93